Details about CWC Mesh — Concrete Weight Coating Reinforcement Mesh for Subsea Pipeline
Product Details
Size & Application
How to order
Video
Product Details
CWC Mesh — Concrete Weight Coating Mesh
CWC Mesh (Concrete Weight Coating Mesh) is the engineered solution for concrete weight coated (CWC) subsea pipelines. Also called Pipeline Reinforced Mesh or Pipeline Concrete Coating Mesh, it provides the tensile reinforcement that keeps the concrete coating intact through transport, installation, and long-term seabed burial.
What separates CWC mesh from commodity welded wire mesh is the deep crimping of longitudinal wires before welding. This creates a wave geometry that locks into wet concrete, distributing stress across the coating and preventing cracking or spalling.
Key Specifications
- Material: Low-carbon steel wire, hot-dip galvanized (ASTM A123, ≥600 g/m²) or electro-galvanized
- Line wires: Deeply crimped, 6 / 8 / 10 wires depending on type
- Cross wire spacing: 50.8 mm (2-inch) or 92.4 mm depending on type
- Exposed wire edge: ≤ 2.5 mm per ASTM A810
- Types: HN-N (6 wires), HN-T (8 wires), HN-L (8 wires, 92.4mm spacing), HN-W (10 wires)
- Pipeline OD range: 6 inches to 60+ inches
- Galvanizing: Hot-dip (standard for subsea) or electro-galvanized (nearshore)
Applications
- Subsea gas transmission pipelines — concrete ballast coating
- Offshore platform infield pipelines — high-pressure, strong-current zones
- Onshore pipeline shore approach sections — marshland and tidal zone burial
- Oil & gas pipelines — anti-buoyancy concrete weight coating
Why CWC Mesh vs. Standard Welded Mesh?
Standard welded mesh has wires simply crossed and spot-welded. CWC mesh line wires are deeply crimped before welding, creating a wave structure that provides genuine mechanical interlock with concrete — not just a physical barrier. For subsea pipelines, this distinction matters:
- Prevents concrete cracking during pipe handling and marine installation
- Distributes thermal and pressure stresses across the coating lifespan
- Hot-dip galvanizing resists corrosion in buried/submerged service for 30+ years
- Controlled exposed edge (≤ 2.5 mm) eliminates stress concentration points
Size & Application
Product Types & Specifications
HN-N — 6 Line Wire CWC Mesh
Low-carbon steel wire, hot-dip galvanized per ASTM A123. Six deeply crimped longitudinal wires are resistance-welded to cross wires at 50.8 mm (2-inch) intervals. The 2-inch spacing between line wires provides a 25.4 mm concrete penetration depth on each side, ensuring 1-inch total overlap per side when panels are butted against the pipe. Exposed wire edge ≤ 2.5 mm per ASTM A810.
| Parameter | Specification |
|---|---|
| Line wires | 6, deeply crimped |
| Cross wire spacing | 50.8 mm (2 inches) |
| Wire diameter (line) | 2.0 – 3.0 mm |
| Wire diameter (cross) | 2.5 – 4.0 mm |
| Best for pipeline OD | 6 – 12 inches (NPS) |
| Panel overlap | 25.4 mm (1 inch) per side |
HN-T — 8 Line Wire CWC Mesh
Spot-welded mesh of galvanized low-carbon steel wire. Eight deeply crimped line wires provide higher reinforcement density compared to HN-N, distributing concrete stress more evenly across the coating cross-section. Standard 50.8 mm cross wire spacing accommodates standard concrete casting pressures. For pipelines 12 – 24 inches OD where higher bending moment resistance is required.
| Parameter | Specification |
|---|---|
| Line wires | 8, deeply crimped |
| Cross wire spacing | 50.8 mm (2 inches) |
| Wire diameter (line) | 2.0 – 3.5 mm |
| Wire diameter (cross) | 2.5 – 4.5 mm |
| Best for pipeline OD | 12 – 24 inches (NPS) |
HN-L — Long Spacing CWC Mesh
Identical wire count to HN-T (8 deeply crimped line wires) but with extended 92.4 mm cross wire spacing. This reduces mesh material weight and cost for longer pipeline spans where bending stresses are lower. The wider spacing maintains adequate concrete interlock while improving cost efficiency for onshore transmission pipeline sections with standard burial conditions.
| Parameter | Specification |
|---|---|
| Line wires | 8, deeply crimped |
| Cross wire spacing | 92.4 mm |
| Wire diameter (line) | 2.0 – 3.5 mm |
| Wire diameter (cross) | 2.5 – 4.5 mm |
| Best for pipeline OD | 24 – 36 inches (NPS) |
HN-W — 10 Line Wire CWC Mesh
Maximum wire density configuration. Ten deeply crimped line wires provide the highest tensile reinforcement capacity for extra-large diameter subsea pipelines (36+ inches OD) subject to high S-lay or J-lay installation stresses and deepwater hydrostatic pressure. Hot-dip galvanizing (≥ 600 g/m²) ensures 30+ year service life in buried seabed conditions.
| Parameter | Specification |
|---|---|
| Line wires | 10, deeply crimped |
| Cross wire spacing | 50.8 mm (2 inches) |
| Wire diameter (line) | 2.5 – 4.0 mm |
| Wire diameter (cross) | 3.0 – 5.0 mm |
| Best for pipeline OD | Over 36 inches (NPS) |
| Galvanizing | Hot-dip, ≥ 600 g/m² |
Custom wire counts, crimp heights, and panel dimensions available for non-standard pipeline OD or special project specifications. Contact us with your project drawing.
How to order
How to Order CWC Mesh
Information to Include in Your Inquiry
To get an accurate quote and lead time, please provide:
- Pipeline outer diameter (OD) and wall thickness
- Concrete coating thickness and target weight per unit length
- Mesh type (HN-N / HN-T / HN-L / HN-W) or specify if custom
- Wire diameter for both line and cross wires (if known)
- Galvanizing method: hot-dip or electro-galvanized
- Quantity: number of panels or total square meters
- Inspection requirements: MTR (Mill Test Reports), third-party inspection
- Project standard: ASTM A810 or other applicable specification
Packaging & Shipping
Standard export packaging: bundles wrapped in rust-inhibiting paper, steel strapped. 20-foot container loads typical. Lead time 2–4 weeks for standard types, 3–5 weeks for custom specifications.
Sample Policy
Sample panels available for specification verification. Contact us with your project details to request samples.
Video









